25% off with code “SUMMER”Run your A algorithm for the same problem using the alternative heuristic function h2n defined in your answer to Question 54 in Homework 2 or a corrected h2n in case your h2n answe
Showing the single result
Showing the single result
Product categories
Filter by price
Top rated products
-
You have been assigned to create a simple stopwatch application for fitness enthusiasts. Develop...
Rated 5.00 out of 5$15.00Original price was: $15.00.$10.00Current price is: $10.00. -
63 Consider the Employee class hierarchy from the beginning of Chapter 6 Use the Template Method
Rated 5.00 out of 5$10.00Original price was: $10.00.$5.00Current price is: $5.00. -
![1. Write a program in MARIE assembly language to perform the following code segment. Test your code thoroughly using the MARIE simulator with values of X=10, X=20, and X=30. What is the value stored in X and Y by the end of execution? Include comments for each line of instruction in your program (12 points). X=10 Y=0 while X!=0 do Y=X X=X-1 endwhile while X!=0 do Y=X X=X-1 endwhile 2. Consider the following program in MARIE assembly language. Complete the table detailing the RTN for the next 3 instructions only that will be executed including the content of registers PC, IR, MAR, MBR, and AC in hexadecimal. Note the first instruction LOAD X is already filled. Note also that the SKIPCOND instruction has no operands, therefore you can complete Fetch, decode and execute cycles only. Explain in one statement what this program is doing (14 points). ORG 000 LOAD X ; AC = X Repeat, ADD One ; AC = X + 1 SKIPCOND 000 ; if AC < 0 then PC = PC + 1 (skip) JUMP End ; Go to End STORE X ; X = AC JUMP Repeat ; Go to Repeat End, STORE X ; Stop (end of program) This program is incrementing the value of X by 1 repeatedly until the value in AC becomes negative. 3. Assume a main memory has the following hex values in the first two bytes: Byte 0: 8F Byte 1: 0F What is the actual decimal value stored in these bytes, assuming they are in 16-bit 2's complement representation and the machine is using: a) Big endian memory b) Little endian memory (4 points) a) In big endian memory, the byte order is reversed. So, the actual decimal value stored in these bytes would be -7. b) In little endian memory, the byte order remains the same. So, the actual decimal value stored in these bytes would be 36655. 4. Consider the assembly program (in MARIE) below and the corresponding memory address for each instruction. Show the symbol table that will be constructed by the assembler after the first pass including the translated program, then fill in the final machine code produced by the assembler after the second pass. Fill in the given tables using HEX numbers for instructions and addresses. (10 points) [Symbol Table] LOAD 0100 ADD 0101 STORE 0110 SUBT 0111 JUMP 1000 Dec1 0001 [First Pass] 0100 LOAD X ; Load value at address X to AC 0101 ADD Y ; Add value at address Y to AC 0110 STORE Z ; Store value in AC to address Z 0111 SUBT X ; Subtract value at address X from AC 1000 JUMP Z ; Jump to address Z [Second Pass] 0100 1005 ; Load X 0101 5006 ; Add Y 0110 210B ; Store Z 0111 1015 ; Subtract X 1000 4010 ; Jump Z](https://gotit-pro.com/wp-content/uploads/2023/10/fa03249e-78f5-4de9-8ddf-1a7a5999f6df-300x362.jpg)
1 Write a program in MARIE assembly language to perform following code segment Test your code
Rated 5.00 out of 5$15.00Original price was: $15.00.$10.00Current price is: $10.00.
Tags
Ask the user to input the file name and path of the first input file
Ask the user to input the file name and path of the output file
Ask the user to input the file name and path of the second input file
Assume that the operands are the letters a through m and the operators are
Continue looping until the user has entered a valid file name and path
Create a TypeScript program that repeats the values 1 to 100 with the following loop operation
Develop an additional 3 derived subclasses named clsRectangle clsTriangle clsCircle which Inherits the properties of the Base Class clsShape
Directions Using best practises in programming design and develop a project based on the following requirements
Each name must be written on a separate line in the output file
Enter the path and name of the first file ctest Terrtxt
For example the expression a b c d should be compiled according to the following tableThe table shows the order in which the operations are performed and operands for each
Hint Use two arrays One for the string names and the other for the string phone numbers
If it is an operand push it onto the operand stack
If it is an operator compare its precedence to that of the operator on top of the operator stack
If the character is neither blank nor an operand nor an operator display an error message and terminate the program
If the current operator has higherprecedence than the one currently on top of the stack or if the stack is empty it should be pushed onto the operator stack
If the file cannot be opened display the appropriate error message and require the user to reenter the file name and path
Internally computers are constructed from circuitry that consists of small onoff switches
Methods should include a default constructor that sets values to the empty string or zero a constructor that allows the user to specify all values for the data items a member metho
Please review the rubric to make sure you meet all of the requirements for this lab
public static String getPhoneNumberString nameArr String phoneNumberArr String contactName int arraySize
Read all the names from one input file at a time
Read names from two different files into your program and write each name to a single new file
Real values of initial velocity at 50 100 150 and 200 ftsec
sale
skinny
So the in the example above the cone is 225 nuts are 050 and cherries are 050 for a total of 325
summer
The database StudentDatamdb located in the email sent and in CanvasFiles is maintained by the University Registrar
The file should be named icecreamtxt and the file will always have exactly three lines of text of the general format
There must be no blank lines between names in the output files
The result column gives the name of an identifier working backward from z chosen to hold each result
The return value of getPhoneNumber is the phone number associated with the specific contact name
This problem demonstrates the use of repetition controlled by a terminating limit
To think and select the proper loop to accomplish different tasks
Use a tryexcept block to read from the input files and write to the output file
When an order is saved the information stored on the disk is the flavor and the extras
Write a client program that uses Stack abstract data to compile a simple arithmetic expression without parentheses
Write a program that reads numbers from an array and graphs the information in the form of a bar chart or histogram
Write a program that reads the names from the two input files and writes the names to the two output files
Write a program to determine the maximum height to which a projectile will travel if atmospheric resistance is neglected for different initial velocities
You must use a for loop to process the second input file nameslist2txt and write to the output file
You must use a while loop to process the first input file nameslist1txt and write to the output file
Your program should read each character and process it as follows If the character is blank ignore it
You would need to deal with the comma using indexOf and substring